Audi Q5 Owners & Service Manuals

Audi Q5: Test Sequence

Battery, Checking, Vehicles with Battery Monitoring Control Module J367 or Energy Management Control Module J644 and Data Bus On Board Diagnostic Interface J533

  • In certain model series the following is responsible for monitoring the electrical system: Energy Management Control Module -J644- or Battery Monitoring Control Module -J367- in connection with the Data Bus On Board Diagnostic Interface -J533-; allocation. Refer to → Wiring diagrams, Troubleshooting & Component locations. The battery test for these vehicles is performed during "Guided Fault Finding".
  • If the battery test is not possible with "Guided Fault Finding" due to a partially or exhaustively discharged battery, the battery can be quickly evaluated with the help of the "battery test via current draw".
  • Maintenance-free batteries must not be opened. Otherwise, the warranty is voided.

  Caution

It is not possible to check the battery using "Guided Fault Finding" through MY 2010 during the following procedure, even if the vehicle has a Battery Monitoring Control Module -J367-:

  • A3 from MY 2004 (8P)
  • TT from MY 2007 (8J)
  • R8 from My 2007 (42)

Battery test. Refer to → Chapter "Checking the Battery - Vehicles without a Battery Monitoring Control Module -J367- or Energy Management Control Module -J644-".

  WARNING

Risk of injury. Follow all warning messages and safety precautions. Refer to → Chapter "Warnings and Safety Precautions".

Perform Tests in the Following Sequence:

1.  Visual inspection. Refer to → Chapter "Visual Inspection".

2.  Check the visual indicator color display (if equipped). Refer to → Chapter "Visual Indicator Color Display, Checking".

  WARNING

Do not check or charge a Battery -A- when the visual indicator has "no color or is bright yellow". Jump starting must not be used!

There is a risk of explosion during testing, charging or jump starting.

These Batteries -A- must be replaced.

3.  Battery Test with Vehicle Diagnostic Tester refer to → Chapter "Battery Test with Vehicle Diagnostic Tester".

Checking the Battery - Vehicles without a Battery Monitoring Control Module -J367- or Energy Management Control Module -J644-

  Caution

It is not possible to check the battery using "Guided Fault Finding" through MY 2010 during the following procedure, even if the vehicle has a Battery Monitoring Control Module -J367-:

  • A3 from MY 2004 (8P)
  • TT from MY 2007 (8J)
  • R8 from My 2007 (42)

  WARNING

Risk of injury. Follow all warning messages and safety precautions. Refer to → Chapter "Warnings and Safety Precautions".

Perform the Tests in the Following Sequence:

1.  Visual inspection. Refer to → Chapter "Visual Inspection".

2.  Check the visual indicator color display (if equipped). Refer to → Chapter "Visual Indicator Color Display, Checking".

  WARNING

Do not check or charge a Battery -A- when the visual indicator has "no color or is bright yellow". Jump starting must not be used!

There is a risk of explosion during testing, charging or jump starting.

These Batteries -A- must be replaced.

  Note

The Battery Tester with Printer -VAS5097A- will no longer be used for warranty testing. Only the Battery Tester -VAS6161- is still being used.

3.  Battery test with:

  • Battery Tester -VAS6161-. Refer to → Chapter "Battery Tester -VAS6161-".
  • Battery Tester with Printer -VAS5097A-. Refer to → Chapter "Battery Tester with Printer -VAS5097A-".

4.  Depending on the result of the battery load test, "perform current draw test". Refer to → Chapter "Current Draw Test".

    READ NEXT:

     Visual Inspection

      WARNING Risk of injury. Follow all warning messages and safety precautions. Refer to → Chapter "Warnings and Safety Precautions". Before any extensive measurements are taken, visuall

     Battery Tester -VAS6161-

    General Description:   WARNING Risk of injury. Follow all warning messages and safety precautions. Refer to → Chapter "Warnings and Safety Precautions". It is not necessary to disconne

     Maintenance Test, Performing

      WARNING Do not check or charge a Battery -A- when the visual indicator has "no color or is bright yellow". Jump starting must not be used! There is a risk of explosion during testing, char

    SEE MORE:

     Overview - Driveshaft

    Overview - Driveshaft, Mounted On Transmission Side   Note Pay attention to the general repair information. Refer to → Chapter "Repair Information". The attached driveshaft can only be separated from the transmission if it is completely removed. No repair work can be carried out on

     Overview - Wheel Bearing

    1 - Nut 40 Nm Always replace if removed 2 - Upper Front Control Arm 3 - Upper Rear Control Arm 4 - Bolt Always replace if removed 5 - Washer 6 - Wheel Bearing Housing Removing and installing. Refer to → Chapter "Wheel Bear

    © 2019-2024 Copyright www.audiq5.net